BETAFPV ELRS 2.4G Meteor65 1S Brushless Whoop Drone

$169.99

Description

BETAFPV ELRS 2.4G Meteor65 1S Brushless Whoop Drone with BT2.0 Connector F4 1S 5A AIO Brushless Flight Controller M03 350mW VTX 19500 KV 0802SE Motor for Long Range Flying FPV Racing Whoop Drone Quad

  • 【SPI ELRS 2.4G RX】Meteor65 ELRS 2.4G 1S drone equipped with the F4 1S 5A AIO brushless FC and SMD ceramic antenna, which integrates BLHeli_S 5A ESC and SPI ExpressLRS 2.4G receiver. It will provide pilots with a stable signal and long-range flying
  • 【M03 350mW VTX】M03 VTX, an ultralight and high output power 5.8GHz analog VTX, is perfect for Meteor65 whoop drone for longer range flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G, pilots can fly whoop drones faster, longer and can easily fly across hinders
  • 【Motor&Props】Comes with 0802SE 19500KV motor and 31mm 3-blade propellers, the KV value is lower, which makes the flight without jitter, pilots can do more movements. Suitable for both indoor and outdoor flight/It provides you more durable and smoother flight experience
  • 【BT2.0 Connector】The new ELRS 2.4G Meteor65 1S whoop drone comes with BT2.0 connector like other Meteor65 versions. It can support 9A continuous current and 15A burst while the PH2.0 connector just supports 4.5A continuous current. Solving the low voltage warning issue of PH2.0 connector on 1S brushless whoop when you start flying
  • 【Notice】All ELRS receiver versions of BETAFPV are the default ELRS1.0 firmware version. If your Module is ELRS2.0, you need to upgrade the firmware of FC first. The receiver on the drone defaults to 500hz refresh rate; Please check if the module also be set to 500hz. For more details, you can contact us via Amazon mailPlease note,
    At present, all ELRS receiver versions of BETAFPV are the default ELRS1.0 firmware version.In this situation, if the ELRS firmware version of your ELRS Nano TX module is 2.0, you may bind it successfully, but you may meet the issue as follow:
    Bind it successfully but the signal is too weak, get receiver lost all the time, etc.

    Since these two firmware versions are not compatible or unstable at the moment.
    And the receiver on the drone defaults to a 500hz refresh rate, so the module must also be set to 500hz.

    More TECHNICAL SUPPORT is needed, BETAFPV is always here with you.

    BETAFPV ELRS 2.4G Meteor65 1S Brushless Whoop Drone with BT2.0 Connector F4 1S 5A AIO Brushless Flight Controller M03 350mW VTX 19500 KV 0802SE Motor for Long Range Flying FPV Racing Whoop Drone Quad

    SPECIFICATION
    Item: ELRS 2.4G Meteor65 1S Brushless Whoop
    Weight: 24.09g
    Power: 1S
    FC&ESC: F4 1S 5A AIO Brushless FC – ELRS 2.4G V1.0
    Motors: 0802SE 19500KV Brushless Motors
    Camera: C02 Camera
    VTX: M03 350mW VTX
    Angle: 30 degree
    Props: Gemfan 31mm 3-Blade 1.0mm Shaft Props
    Receiver: SPI ELRS 2.4G Receiver (Keep the external receiver port)
    Battery: BT2.0 300mAh 1S Lipo
    Flight time: 2:00-3:00 minutes

    Q: Comparison with the SPI Frsky version, what is the upgrade point on the new ELRS 2.4G version drone?
    A1: The FC board is the F4 1S 5A FC (ELRS 2.4G), which integrates BLHeli_S 5A ESC and SPI ExpressLRS 2.4G receiver.
    A2: 5.8G VTX M03 could provide highest 350mW output power. So both the radio link and FPV video link could be long enough.

    PACKAGE
    1 * Meteor65 Brushless Whoop Quadcopter (1S)
    2 * 300mAh 1S 30C Battery with BT2.0 connector
    1 * BT2.0 Battery Charger and Voltage Tester
    1 * TypeC USB cable
    1 * Customized Carry Case
    1 * Spare 31mm 3-blade props (1.0mm Shaft)
    1 * Screwdriver